cisco.ise.ipsec_bulk module – Resource module for Ipsec Bulk

Note

This module is part of the cisco.ise collection (version 2.9.0).

To install it, use: ansible-galaxy collection install cisco.ise. You need further requirements to be able to use this module, see Requirements for details.

To use it in a playbook, specify: cisco.ise.ipsec_bulk.

New in cisco.ise 1.0.0

Synopsis

• Manage operation create of the resource Ipsec Bulk.

Note

This module has a corresponding action plugin.

Requirements

The below requirements are needed on the host that executes this module.

• ciscoisesdk >= 2.2.0

• python >= 3.5

Parameters

Parameter	Comments
ise_debug boolean	Flag for Identity Services Engine SDK to enable debugging. Choices: :ansible-option-choices-entry-default:`false` ← (default) :ansible-option-choices-entry:`true`
ise_hostname string / required	The Identity Services Engine hostname.
ise_password string / required	The Identity Services Engine password to authenticate.
ise_single_request_timeout integer added in cisco.ise 3.0.0	Timeout (in seconds) for RESTful HTTP requests. Default: :ansible-option-default:`60`
ise_username string / required	The Identity Services Engine username to authenticate.
ise_uses_api_gateway boolean added in cisco.ise 1.1.0	Flag that informs the SDK whether to use the Identity Services Engine’s API Gateway to send requests. If it is true, it uses the ISE’s API Gateway and sends requests to https://{{ise_hostname}}. If it is false, it sends the requests to https://{{ise_hostname}}:{{port}}, where the port value depends on the Service used (ERS, Mnt, UI, PxGrid). Choices: :ansible-option-choices-entry:`false` :ansible-option-choices-entry-default:`true` ← (default)
ise_uses_csrf_token boolean added in cisco.ise 3.0.0	Flag that informs the SDK whether we send the CSRF token to ISE’s ERS APIs. If it is True, the SDK assumes that your ISE CSRF Check is enabled. If it is True, it assumes you need the SDK to manage the CSRF token automatically for you. Choices: :ansible-option-choices-entry-default:`false` ← (default) :ansible-option-choices-entry:`true`
ise_verify boolean	Flag to enable or disable SSL certificate verification. Choices: :ansible-option-choices-entry:`false` :ansible-option-choices-entry-default:`true` ← (default)
ise_version string	Informs the SDK which version of Identity Services Engine to use. Default: :ansible-option-default:`"3.1\_Patch\_1"`
ise_wait_on_rate_limit boolean	Flag for Identity Services Engine SDK to enable automatic rate-limit handling. Choices: :ansible-option-choices-entry:`false` :ansible-option-choices-entry-default:`true` ← (default)
ItemList list / elements=dictionary	Ipsec Bulk’s ItemList.
authType string	Authentication type for establishing connection.
certId string	ID of the certificate for establishing connection.
configureVti boolean	Authentication type for establishing connection. Choices: :ansible-option-choices-entry:`false` :ansible-option-choices-entry:`true`
espAhProtocol string	Encryption protocol used for establishing connection.
hostName string	Hostname of the node.
iface string	Ethernet port of the node.
ikeReAuthTime integer	IKE re-authentication time.
ikeVersion string	IKE version.
localInternalIp string	Local Tunnel IP address.
modeOption string	The Mode type used for establishing the connection.
nadIp string	NAD IP address for establishing connection.
phaseOneDHGroup string	Phase-one DH group used for establishing connection.
phaseOneEncryptionAlgo string	Phase-one encryption algorithm used for establishing connection.
phaseOneHashAlgo string	Phase-one hashing algorithm used for establishing connection.
phaseOneLifeTime integer	Phase-one connection lifetime.
phaseTwoDHGroup string	Phase-two DH group used for establishing connection.
phaseTwoEncryptionAlgo string	Phase-two encryption algorithm used for establishing connection.
phaseTwoHashAlgo string	Phase-two hashing algorithm used for establishing connection.
phaseTwoLifeTime integer	Phase-two connection lifetime.
psk string	Pre-shared key used for establishing connection.
remotePeerInternalIp string	Remote Tunnel IP address.
operation string	Ipsec Bulk’s operation.

Notes

Note

• SDK Method used are native_ipsec.NativeIpsec.bulk_ip_sec_operation,

• Paths used are post /api/v1/ipsec/bulk,

• Does not support check_mode

• The plugin runs on the control node and does not use any ansible connection plugins, but instead the embedded connection manager from Cisco ISE SDK

• The parameters starting with ise_ are used by the Cisco ISE Python SDK to establish the connection

Examples

- name: Create
  cisco.ise.ipsec_bulk:
    ise_hostname: "{{ise_hostname}}"
    ise_username: "{{ise_username}}"
    ise_password: "{{ise_password}}"
    ise_verify: "{{ise_verify}}"
    ItemList:
    - authType: string
      certId: string
      configureVti: true
      espAhProtocol: string
      hostName: string
      iface: string
      ikeReAuthTime: 0
      ikeVersion: string
      localInternalIp: string
      modeOption: string
      nadIp: string
      phaseOneDHGroup: string
      phaseOneEncryptionAlgo: string
      phaseOneHashAlgo: string
      phaseOneLifeTime: 0
      phaseTwoDHGroup: string
      phaseTwoEncryptionAlgo: string
      phaseTwoHashAlgo: string
      phaseTwoLifeTime: 0
      psk: string
      remotePeerInternalIp: string
    operation: string

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Description
ise_response dictionary	A dictionary or list with the response returned by the Cisco ISE Python SDK Returned: always Sample: :ansible-rv-sample-value:`{"id": "string"}`

Authors

• Rafael Campos (@racampos)

Collection links

Issue Tracker Repository (Sources)